When Linux boots, it displays a “BogoMips” number. What does that mean? Is the number displayed correct? What use is the infromation? This quintessential part of Linux is demystified in this article.
Some device drivers in the Linux kernel need timing delays. Either they need a very short delay, or the delay must be very accurately determined. A simple non-busy loop cannot do this. Therefore, Linus Torvalds added a calibration in the boot procedure to predetermine how often a specific busy-loop algorithm can be calculated in one second. This predetermined value, called loops_per_second, is used in the device drivers to delay for precisely measured times.
For fun, Linus also added a print statement presenting this predetermined value (divided by 500,000) as BogoMips. Linus apparently loves it when millions of Linux users are gazing at their computer, baffled by these bogus MIPS. Note that BogoMips have nothing to do with the million instructions per second that the name suggests; that is why they are bogus.
The only serious reason for paying attention to the BogoMips presented on booting Linux is to see whether it is in the proper range for the particular processor, its clock frequency, and the potentially present cache. 486 systems are especially prone to faulty setups of RAM caching, turbo-buttons, and such things.
People continuously ask on Usenet: “I have an XYZ CPU running at clock MHz. How many BogoMips should it do?” The answer can be calculated from the following table:
Intel/AMD 386SX clock * 0.14 (± 0.01) Intel/AMD 386DX clock * 0.18 (± 0.01) Cyrix/IBM 486 clock * 0.33 (± 0.04) Intel/AMD 486 clock * 0.50 (± 0.01) Pentium clock * 0.40 (± 0.01) 680x0 (insufficient data) PowerPC clock * 0.77 (± 0.02) Mips (insufficient data) Alpha clock * 0.99 (± 0.01)
From the above calculation we see several important points. First of all, the Intel and AMD 486 CPUs are not showing the same BogoMips as Cyrix and IBM 486 CPUs. This does not mean that they have a different perceived performance; it just means that they process the busy-loop algorithm differently.
The table also shows that the Pentium processor doesn't have the expected extrapolated multiplication factor. This is due to the fact that the specific busy-loop algorithm is not optimized for the parallelism of the Pentium processor.
The BogoMips calculations for the Motorola, PowerPC, Mips, and Alpha processors are similar to the Intel type processors calculations. Because the non-busy loop algorithm is coded in Assembler, however, they cannot be identical. It clearly shows that comparison of BogoMips between CPUs is really bogus, even between two different Intel type CPUs.
Last but not least, you see an allowed variation in the multiplication factor of about 0.01. The BogoMips calculation loop is “quantizised” (Linus's term), so it is likely that you will get exactly the same number all the time. Yet, if the speed is just on the edge, small variations, such as different lengths for interrupts, will cause your machine's BogoMips to vary.
“When I boot Linux I get the message:
Calibrating delay loop.. ok - 23.96 BogoMips failed
Where or why has the calibration delay loop failed?”
The obvious answer is that it didn't fail. If it had failed the text would have been:
Calibrating delay loop.. failed
What likely did fail was a driver for some gadget which may not be in the machine. The point is that just after calculating the BogoMips, all device drivers are initialized: first the SCSI devices, then Net devices, etc. Any failure in these initializations is duly reported. The AHA152x drive is noted for such failures. Other effects of failing drivers (and not of failing BogoMips calculations) are systems crashes, long waits, and complete system lock-ups.
Since Linux 1.2, many error messages have improved, so upgrade to at least that version to find out which particular driver is failing.
For people without Linux systems, or for those people who do not want to reboot their system time and again, a stand-alone program for calculating BogoMips is available in the standard archives (e.g., on sunsite.unc.edu in /pub/Linux/system/Status/bogo-1.2.tar.gz). On Linux, by default, it runs the same code that is used in the Linux kernel while booting, but runs as a user program. Note that due to system load, values calculated with the stand-alone program may be lower than expected for the CPU you are running, and lower than reported during boot. For the non-Linux systems, a portable C version is available that may run on any system that supports an ANSI C compiler and library.
The BogoMips mini-HOWTO gives a full table of reported BogoMips for various systems. More than 250 BogoMips references as reported on Usenet, or sent directly by e-mail to the maintainer, are listed with information about CPU type, clock speed, BogoMips, and the name and e-mail address of the reporter. For example, the lowest and highest BogoMips reported in the current version of The BogoMips Mini-HOWTO are:
The Lowest: H. Peter Anwin pa@nwu.edu 386SX/16 387 nocache 0.57 BogoMips The Highest: David Mosberger-Tang davidm@cs.arizona.edu Alpha 21064A/275 273.37 BogoMips
In the BogoMips mini-HOWTO, values that do and do not comply with the aforementioned BogoMips calculation methods are listed. The non-complying group is named “Oddly or Faultily configured” because non-compliance does not necessarily mean that the system is faultily configured.
The BogoMips may be used to see whether your system is faster than mine. Of course this is completely wrong, unreliable, ill-founded, and utterly useless, but all benchmarks suffer from this problem, so why not use it? This inherent stupidity has never before stopped people from using benchmarks, has it? [Note for the humor-challenged: no angry letters to the editor will be accepted on this point. —Ed]